Campbell-hausfeld WG3060 User Manual download pdf (Page 6)

Wire Feed Arc Welder

*NOTE: Campbell Hausfeld regulator

WT600100AV is factory preset at 30 cfh.

No adjustment is necessary. Also, a pop-

out indicator in the end of the regulator

shows the amount of gas left in the

cylinder. When not extended, there is

approximately 10 minutes of welding

left before the cylinder is empty.

7. Remember to close the gas valve

when finished welding.

1. Be sure to read,

understand, and comply

with all precautions in

the General Safety

Information section. Be

sure to read the entire section

entitled Welding Guidelines prior to

using this equipment.

2. Verify welder is off.

3. Verify that the surfaces of metals to

be joined are free from dirt, rust,

paint, oil, scale or other contam-

inants. These contaminants make

welding difficult and cause poor

welds.

All persons operating this

equipment or in the area

while equipment is in use

must wear protective welding gear

including: eye protection with proper

shade, flame resistant clothing, leather

welding gloves, and full foot

protection.

WHETHER OR

NOT THE TRIGGER

IS PULLED, the WG3000 welding

wire is LIVE

whenever the welder

is turned ON

If heating, welding, or

cutting materials that are

galvanized, zinc plated, lead,

or cadmium plated refer to the General

Safety Information Section for

instructions. Extremely toxic fumes are

created when these metals are heated.

4. Connect the work clamp to the

work piece or workbench (if metal).

Make sure the contact is secure.

Avoid surfaces with paint, varnish,

corrosion, or non-metallic materials.

5. Position the Heat Selector on the

front panel to the desired setting.

See application decal inside door of

wire feed compartment for proper

heat settings.

NOTE: These settings are general

guidelines only. Heat setting may vary

according to welding conditions and

materials.

6. Rotate the Wire Speed Control to

setting number 5 to start with, then

adjust as needed after test weld.

7. Plug the input cord into a proper

voltage receptacle with proper

circuit capacity (See Chart under

circuit requirements on page 1).

8. Switch the welder ON.

9. Verify that the wire is extended

1/4” from the contact tip. If not,

squeeze the trigger to feed

additional wire, release the trigger,

and cut wire to proper length.

10. Position the wire feed gun near the

work piece, lower the welding

helmet by nodding the head, or

position the hand shield, and

squeeze the gun trigger. Adjust heat

setting and wire speed as needed.

11. When finished welding, turn welder

off and store properly.

Disconnect power

supply and turn

machine off before inspecting or

servicing any components. Keep the

wire compartment cover closed at all

times unless the wire needs

replacement.

Before every use:

1. Check condition of weld cables and

immediately repair or replace any

cables with damaged insulation.

2. Check condition of power cord and

immediately repair or replace any

cord if damaged.

3. Inspect the condition of the gun tip

and nozzle. Remove any weld slag.

Replace gun tip or nozzle if

damaged.

Do not operate this

welding machine

with cracked or missing insulation on

welding cables, wire feed gun, or

power cord.

Every 3 months:

1. Replace any unreadable safety

labels on the welder.

2. Use compressed air to blow all dust

and lint from the ventilation

openings.

3. Clean the wire groove on the drive

roll. Remove wire from the feed

mechanism, remove screws from the

drive roll housing. Use a small wire

brush to clean the drive roll. Replace

if worn or damaged.

Consumer and Wear Parts

The following parts require routine

maintenance:

• Wire feed drive roller

• Gun liner - replace if worn

• Nozzle/contact tips

• Wire - this welder will accept either

4” or 8” diameter spools. Welding wire

is susceptible to moisture and oxidizes

over time, so it is important to select a

spool size that will be used within

approximately 6 months. For mild steel

welding, AWS ER70S6 solid wire or

AWS E71T-GS flux-core wire is

recommended.

• Contact tips - use Campbell Hausfeld,

Tweco

, and other compatible tips.

Pop-out

Indicator

Cap

Adapter

ARGON OR

ARGON MIX

INSTALLATION

Figure 8 - Hookup

Operation

Maintenance

MANUAL

Shielding Gas

Installation (Continued)

www.campbellhausfeld.com

1 2 3 4 5 6 7 8 9 10 11 ... 47 48

Comments to this Manuals

No comments

Campbell-hausfeld WG3060 User Manual Page 6

Comments to this Manuals

Related products and manuals for Voice Recorders Campbell-hausfeld WG3060