Campbell-hausfeld WS0970 User Manual download pdf (Page 2)

35 Sp

Modelo WS0970

Notas

Shielded Metal Arc Welder

General Safety

(Continued)

 Before starting or servicing any

electric arc welder, read and

understand all instructions. Failure

to follow safety precautions or

instructions can cause equipment

damage and or serious personal

injury or death.

 All installation, maintenance, repair

and operation of this equipment

should be performed by qualified

persons only in accordance with

national, state, and local codes.

Improper use of electric arc

welders can cause electric

shock, injury, and death!

Take all precautions

described in this manual to reduce the

possibility of electric shock.

 Verify that all components of the

arc welder are clean and in good

condition prior to operating the

welder. Be sure that the insulation

on all cables, electrode holders, and

power cords is not damaged.

Always repair or replace damaged

components before operating the

welder. Always keep welder panels,

shields, etc. in place when operating

the welder.

 Always wear dry protective clothing

and welding gloves, and insulated

footwear.

 Always operate the welder in a

clean, dry, well ventilated area. Do

not operate the welder in humid,

wet, rainy, or poorly ventilated

areas.

 Be sure that the work piece is

properly supported and grounded

prior to beginning any electric arc

welding operation.

 Coiled welding cable should be spread

out before use to avoid overheating

and damage to insulation.

Never immerse the

electrode or

electrode holder in water. If the welder

becomes wet for any reason, be

absolutely certain that it is completely

clean and dry prior to attempting use!

DANGER

WARNING

 Always shut the equipment off and

unplug the power prior to moving

the unit.

 Always attach the work lead first.

 Verify that the work piece is

securely grounded.

 Always shut off electric arc welding

equipment when not in use and

remove the electrode from the holder.

 Never allow any part of the body to

touch the electrode and ground or

grounded work piece at the same time.

 Awkward welding conditions and

positions can be electrically hazardous.

When crouching, kneeling or at

elevations, be sure to insulate all

conductive parts, wear appropriate

protective clothing, and take

precautions to prevent injury from falls.

 Never attempt to use this

equipment at current settings or

duty cycles higher than those

specified on the equipment labels.

 Never use an electric arc welder to

thaw frozen pipes.

Flying sparks and hot metal

can cause injury. As welds

cool, slag can be thrown off.

Take all precautions described in this

manual to reduce the possibility of

injury from flying sparks and hot metal.

 Wear ANSI approved face shield or

safety glasses with side shield

protection when chipping or

grinding metal parts.

 Wear ear plugs when welding

overhead to prevent spatter or slag

from falling into ears.

Electric arc welding

operations produce intense

light and heat and ultraviolet

(UV) rays. This intense light and UV rays

can cause injury to eyes and skin. Take

all precautions described in this manual

to reduce the possibility of injury to

eyes and skin.

 All persons operating this

equipment or in the area while

equipment is in use must wear

protective welding gear including:

welding helmet or shield with at

least shade 10, flame resistant

WARNING

clothing, leather welding gloves,

and full foot protection.

Never look at arc

welding operations

without eye protection as described

above. Never use a shade filter lens

that is cracked, broken, or rated below

number 10. Warn others in the area not

to look at the arc.

Electric arc welding

operations cause sparks and

heat metal to temperatures

that can cause severe burns! Use

protective gloves and clothing when

performing any metal working

operation. Take all precautions

described in this manual to reduce the

possibility of skin and clothing burns.

 Make sure that all persons in the

welding area are protected from

heat, sparks, and ultraviolet rays.

Use additional face shields and

flame resistant barriers as needed.

 Never touch work pieces until

completely cooled.

Heat and sparks produced

during electric arc welding

and other metal working

operations can ignite flammable and

explosive materials! Take all

precautions described in this manual to

reduce the possibility of flames and

explosions.

 Remove all flammable materials

within 35 feet (10.7 meters) of

welding arc. If removal is not

possible, tightly cover flammable

materials with fire proof covers.

 Do not operate any electric arc

welder in areas where flammable or

explosive vapors may be present.

 Take precautions to be sure that

flying sparks and heat do not cause

flames in hidden areas, cracks,

behind bulkheads, etc.

Fire hazard! Do not weld on

containers or pipes that

contain or have contained

flammable materials or gaseous or

liquid combustibles.

Arc welding closed cylinders

or containers such as tanks

or drums can cause

WARNING

www.chpower.com

1 2 3 4 5 6 7 ... 17 18

Comments to this Manuals

No comments

Campbell-hausfeld WS0970 User Manual Page 2

Comments to this Manuals

Related products and manuals for Tools Campbell-hausfeld WS0970